Hyundai Equus Manuals

Hyundai Azera: Instrument Cluster Repair procedures - Indicators And Gauges - Body Electrical System - Hyundai Azera 2011-2024 Service ManualHyundai Azera: Instrument Cluster Repair procedures

Fifth generation HG (2011–2024) / Hyundai Azera 2011-2024 Service Manual / Body Electrical System / Indicators And Gauges / Instrument Cluster Repair procedures

Inspection
Speedometer
1.
Adjust the pressure of the tires to the specified level.
2.
Drive the vehicle onto a speedometer tester. Use wheel chocks (A) as appropriate.
3.
Check if the speedometer indicator range is within the standard values.
   
Do not operate the clutch suddenly or increase/ decrease speed rapidly while testing.
   
Tire wear and tire over or under inflation will increase the indication error.

[km/h - CANADA]
Velocity
(km/h)
Tolerance
(km/h)
Velocity
(km/h)
Tolerance
(km/h)
20
+0.1
+2.1
160
+1.0
+5.9
40
+0.2
+2.7
180
+1.2
+6.1
60
+0.3
+3.3
200
+1.4
+6.3
80
+0.4
+4.1
220
+1.6
+6.5
100
+0.5
+4.8
240
+1.8
+6.7
120
+0.6
+5.2
260
+2.0
+7.2
140
+0.7
+5.6
?
?

[MPH - USA]
Velocity
(MPH)
Tolerance
(MPH)
Velocity
(MPH)
Tolerance
(MPH)
10
+0.0
+1.3
100
+1.0
+4.1
20
+0.2
+1.5
120
+1.2
+4.3
40
+0.4
+2.1
140
+1.4
+4.4
60
+0.6
+2.7
160
+1.6
+4.8
80
+0.8
+3.5
?
?

Tachometer
1.
Connect the GDS to the diagnostic link connector or install a tachometer.
2.
With the engine started, compare the readings of the tester with that of the tachometer. Replace the tachometer if the tolerance is exceeded.
   
1.
Reversing the connections of the tachometer will damage the transistor and diodes inside.
2.
When removing or installing the tachometer, be careful not to drop it or subject it to severe shock.
Revolution (rpm)
 Tolerance (rpm)
Revolution (rpm)
 Tolerance (rpm)
1,000
±100
5,000
±100
2,000
±100
6,000
±100
3,000
±100
7,000
±100
4,000
±100
8,000
±100

Fuel Gauge
1.
Disconnect the fuel sender connector from the fuel sender.
2.
Connect a 3.4 watt, 12V test bulb to terminals 1 and 3 on the wire harness side connector.
3.
Turn the ignition switch to the ON, and then check that the bulb lights up and the fuel gauge needle moves to full.

Main Fuel Gauge Sender
1.
Using an ohmmeter, measure the resistance between terminals 1 and 3 of sender connector (A) at each float level.

2.
Also check that the resistance changes smoothly when the float is moved from "E" to "F".
Position
Segment
Resistance (?)
Liter (?)
Warning lamp ON
1 SEG
170? ± 2?
8.5
Warning lamp OFF
2 SEG
146.7?
13.9
1/2
6 SEG
72.7?
35
F
12 SEG
15? ± 1?
66

3.
If the height resistance is unsatisfied, replace the fuel sender as an assembly.
   
After completing this test, wipe the sender dry and reinstall it in the fuel tank.
Brake Fluid Level Warning Switch
1.
Remove the connector (A) from the switch located at the brake fluid reservoir.
2.
Verify that continuity exists between switch terminals 1 and 2 while pressing the switch (float) down with a rod.

Brake Fluid Level Warning Lamp
1.
Ignition "ON"
2.
Release the parking brake.
3.
Remove the connector from the brake fluid level warning switch.
4.
Ground the connector at the harness side.
5.
Verify that the warning lamp lights.
Parking Brake Switch
The parking brake switch (A) is a pulling type. It is located under the parking brake lever. To adjust, move the switch mount up and down with the parking brake lever released all the way.
1.
Check that there is continuity between the terminal and switch body with the switch ON (Lever is pulled).
2.
Check that there is no continuity between the terminal and switch body with the switch OFF (Lever is released).
If continuity is not as specified, replace the switch or inspect its ground connection.

Door Switch
Remove the door switch and check for continuity between the terminals.

Seat Belt Switch
1.
Remove the connector from the switch.
2.
Check for continuity between terminals.
Seat belt condition
Continuity
Fastened
Non-conductive (??)
Not fastened
Conductive (?)

Seat Belt Warning Lamp
With the ignition switch turned ON, verify that the lamp glows.
Seat belt condition
Warning lamp
Fastened
OFF
Not fastened
ON

Removal
Instrument Cluster
1.
Disconnect the negative (-) battery terminal.
2.
Tilt the steering column down.
3.
Remove the cluster facia panel after removing the screws.
4.
Remove the instrument cluster (A) after loosening the screws.

5.
Disconnect the cluster connector (A), then remove the cluster.

Installation
Instrument Cluster
1.
Install the cluster to the cluster housing.
2.
Install the cluster fascia lower panel.
Instrument Cluster Description and Operation
Description System block diagram High speed CAN communication : C-CAN 1. User option : Seat Easy Access, Welcome Light, etc 2. SPAS: Smart Parking Aid System 3. EPB : Electronic Parking ...

Troubleshooting
Troubleshooting SymptomPossible causeRemedySpeedometer does not operateCluster fuse (10A) blownCheck for short and replace fuseSpeedometer faultyCheck speedometerCAN line faultyCheck the TCUWirin ...

See also:

26 Brake Control Solenoid Valve(26/B_VFS) Schematic Diagrams
Circuit Diagram ...

Front Seat Shield Inner Cover Components and Components Location
Component Location 1. Front seat shield inner cover ...

Special Service Tools
Special Tools Tool(Number and Name)IllustrationUse09495-3K000Band installerInstallation of ear type boot band09495-33000PullerRemove the spider assembly from the driveshaft ...

Categories

Hyundai Azera Manuals


© 2011-2024 Copyright www.hgmanual.com