Hyundai Equus Manuals

Hyundai Azera: Troubleshooting - Lighting System - Body Electrical System - Hyundai Azera 2011-2024 Service ManualHyundai Azera: Troubleshooting

Troubleshooting
1.
The lamp switch inputs can be checked using the GDS.
2.
To check the input value of lamp switch, select option "IPM".
3.
To consult the present input/output value of IPM, "Current DATA". It provides information of IPM input/output conditions of power supply, turn signal/brake lamp, headlamp, door, locks, outside mirror, wiper, auto-light and transmitters etc.

4.
To check the input value of lamp switch in force mode, select option "Actuation Test of smart junction box".

Symptom
Possible cause
Remedy
One lamp does not light
(all exterior)
Bulb burned out
Replace bulb
Socket, wiring or ground faulty
Repair if necessary
Head lamps do not light
Bulb burned out
Replace bulb
Ignition fuse (LOW:10A, HIGH:20A) blown
Check for short and replace fuse
Head lamp fuse (15A) blown
Check for short and replace fuse
Head lamp relay faulty
Check relay
Lighting switch faulty
Check switch
Wiring or ground faulty
Repair if necessary
Tail lamps and license plate lamps do not light
Bulb burned out
Replace bulb
Tail lamp fuse (10A) blown
Check for short and replace fuse
Tail lamp relay faulty
Check relay
Lighting switch faulty
Check switch
Wiring or ground faulty
Repair if necessary
Stop lamps do not light
Bulb burned out
Replace bulb
Stop lamp fuse (15A) blown
Check for short and replace fuse
Stop lamp switch faulty
Adjust or replace switch
Wiring or ground faulty
Repair if necessary
Stop lamps do not turn off
Stop lamp switch faulty
Repair or replace switch
Instrument lamps do not light
(Tail lamps light)
Rheostat faulty
Check rheostat
Wiring or ground faulty
Repair if necessary
Turn signal lamp does not flash on one side
Bulb burned out
Replace bulb
Turn signal switch faulty
Check switch
Wiring or ground faulty
Repair if necessary
Turn signal lamps do not light
Bulb burned out
Replace bulb
Turn signal lamp fuse (10A) blown
Check for short and replace fuse
Flasher unit faulty
Check flasher unit
Turn signal switch faulty
Check switch
Wiring or ground faulty
Repair if necessary
Hazard warning lamps do not light
Bulb burned out
Replace bulb
Hazard warning lamp fuse (15A) blown
Check for short and replace fuse
Flasher unit faulty
Check flasher unit
Hazard switch faulty
Check switch
Wiring or ground faulty
Repair if necessary
Flasher rate too slow or too fast
Lamps' wattages are smaller or larger than specified
Replace lamps
IPM faulty
Check IPM
Back up lamps do not light
Bulb burned out
Replace bulb
Back up lamp fuse (10A) blown
Check for short and replace fuse
Back up lamp switch (M/T) faulty
Check switch
Transaxle range switch (A/T) faulty
Check switch
Wiring or ground faulty
Repair if necessary
Room lamp does not light
Bulb burned out
Replace bulb
Room lamp fuse (10A) blown
Check for short and replace fuse
Room lamp switch faulty
Check switch
Wiring or ground faulty
Repair if necessary
Front fog lamps do not light
Bulb burned out
Replace bulb
Front fog lamp fuse (15A) blown
Check for short and replace fuse
Front fog lamp relay faulty
Check relay
Front fog lamp switch faulty
Check switch
Wiring or ground faulty
Repair if necessary
Rear fog lamps do not light
Rear fog lamp fuse (15A) blown
Check for short and replace fuse
Rear fog lamp fuse (15A) blown
Check for short and replace fuse
Rear fog lamp switch faulty
Check switch
Rear fog lamp relay faulty
Check relay
Wiring or ground faulty
Repair if necessary
 
Map lamp does not light
Bulb burned out
Replace bulb
Room lamp fuse (10A) blown
Check for short and replace fuse
Map lamp switch faulty
Check switch
Wiring or ground faulty
Repair if necessary
Trunk lamp does not light
Bulb burned out
Replace bulb
Room lamp fuse (10A) blown
Check for short and replace fuse
Wiring or ground faulty
Repair if necessary

Trunk Lamps Repair procedures
Removal 1. Disconnect the negative (-) battery terminal. 2. Remove the luggage room lamp (B) when prying the clip (A) with a flat-up screwdriver. 3. Remove the luggage room lamp bulb in ca ...

Auto Lighting Control System
...

See also:

Line Pressure Control Solenoid Valve Repair procedures
Inspection 1. Turn ignition switch OFF. 2. Disconnect the solenoid valve connector. 3. Measure resistance between sensor signal terminal and sensor ground terminal. 4. Check that the ...

Blade inspection
Commercial hot waxes applied by automatic car washes have been known to make the windshield difficult to clean. Contamination of either the windshield or the wiper blades with foreign matter can re ...

Height Adjust Components and Components Location
Component Location 1. Height adjust ...

Categories

Hyundai Azera Manuals


© 2011-2024 Copyright www.hgmanual.com