Hyundai Azera: Description and Operation

Description

-	Transmitter with 4 buttons (door locking, door unlocking, panic, and trunk release)

-	Receiver is integrated in the IPM control unit

-	IPM, control unit in which remote control decoding is done

RKE Data Flow

Input / Output Interface

Function	Characteristics	Name
		Signal Label	Spec. Designation
Input	Logic	L_ACC	Accessory Signal
		L_IGN2	Ignition 2 Signal
		L_KeyIn	Key In signal
	Analog	A_IGN1	Ignition 1 Signal
	CAN_C Communication	RC_KeylessCodesave	Diagnostic Tool Command for RKE Key Teaching
Output	Internal	b_RFRKELockCmd	RKE Lock Command from RKE Key
		b_RFRKEPanicStartCmd	RKE Panic Start Command from RKE Key
		b_RFRKEPanicStopCmd	RKE Panic Stop Command from RKE Key
		b_RFRKETrunkTGateOpenCmd	RKE Trunk/Tailgate Open Command from RKE Key
		b_RFRKEUnlockCmd	RKE Unlock Command from RKE Key
	CAN_C Communication	CF_Gway_KeyTeachingSound	Internal Warning Buzzer command for RKE Key Teaching Sound
		C_RKECMD	RKE Command to other ECU

•

The Burglar Alarm System is a function used to prevent or deter the unauthorized appropriation of the vehicle. Theft prevention or Burglar Alarm function has been introduced to assert the ownership whenever the rightful owner is physically present. In an attempt to discourage theft, Burglar Alarm works by emitting high-volume sound (Horn) when triggered by circuit breach. This vehicle alarm is designed to be triggered by opening special switches (e.g. doors, hood, trunk open switch contacts)

•	This system also prevents the car from starting by disabling Starter relay if intrusion has been detected.

•

To indicate that the vehicle is anti-theft protected a blinking indicator located at a visible area in the vehicle is provided (this is part of a theft preventive action). The Alarm System function group consists of an Burglar Alarm function. The BurglarAlarm offers a theft protection functions which

1.	Armed by A. Mechanical key lock switch in driver side door if Mechanical Option is set B. By RKE lock or SMK lock command C. All door lock and then all door closed if Mechanical Option is set

2.	Triggers an alarm when A. Any doors open B. Hood open C. Trunk open by unknown event

3.	Disarmed by A. Turning the mechanical key unlock switch in driver side door if Mechanical Option is set B. By RKE unlock or SMK unlock command

Burglar Alarm Function Data Flow

Function	Characteristics	Name
		Signal Label	Spec. Designation
Input	Logic	L_HoodSW	Hood Switch Status
		L_KeyIn	Key In signal
		L_TrunkKeyUnlockSW	Trunk Key Unlock Switch
		L_TrunkStatus	Trunk Switch Status
	CAN_B Communication	C_DRVKeyLockSW	Driver Key Lock signal
		C_DRVKeyUnlockSW	Driver Key Unlock signal
		C_PassiveTrunk_TG	Trunk open command by SMK
		C_SMK_FOB_ID	RKE Command ID or Passive Access Command ID
	CAN_C Communication	CF_Clu_AltLStatus	Engine is running
	Internal	b_AllDoorsClose	All Doors Open/Close State
		b_AllDoorsLock	All Doors Lock/Unlock State
		b_ImmoAuth	Authentication by Immobilizer Function
		b_KeyIGNOn	Key In and IGN1/2  On state
		b_KeyOnState	Key In or Fob In or Terminal On state
		b_PassiveLockCmd	SMK Passive Lock Command
		b_PassiveUnlockCmd	SMK Passive Unlock Command
		b_RKELockCmd	RKE Lock Command
		b_RKETrunkCmd	RKE Trunk Command
		b_RKEUnlockCmd	RKE Unlock Command
Output	Internal	b_ArmBuzzerCmd	ARM Buzzer Command
		b_ArmFlasherCmd	ARM Flasher Command
		b_AutolockCmd	Lock request by Auto Locking
		b_BAlarmFlasherCmd	ALARM Flasher Operation Command
		b_BAlarmHornCmd	ALARM Horn Operation Command
		b_BAState	Burglar Alarm State is in ARM type state
		b_DisarmBuzzerCmd	DISARM Buzzer Command
		b_DisarmFlasherCmd	DISARM Flasher Command
		b_TrunkCloseBuzzerCmd	Trunk Close Buzzer Command
		b_TrunkCloseFlasherCmd	Trunk Close Flasher Command
		b_TrunkOpenFlasherCmd	Trunk Open Flasher Command
		BAlarmState	Burglar Alarm State Information (all state indicated)
	Logic	O_SecurityIND	Security LED
		O_StartInhibition	Burglar Alarm Control (Starter inhibition)
	CAN_B Communication	C_BAlarmState	Burglar Alarm State Information (all state indicated)
		C_BAState	Burglar Alarm State is in ARM type state
		C_FOB1	FOB ID 1 at the origin of the change C_BAState from 0 to 1
		C_FOB2	FOB ID 2 at the origin of the change C_BAState from 0 to 1
		C_Relock	AntiTheft Command

Burglar Alarm Control Function

•

ARM Mode

•	DISARM Mode

•	ARMWAIT Mode

•	ALARM Mode

•	ARMHOLD Mode

•	AutoLockTimer1 Mode

•	AutoLockTimer2 Mode

•	PREARM Mode

No	Pre-condition	Event	Result	Remark
1	All Entrances Closed	All kind of Lock	ARM Flash ARM Buzzer	Stay ARMWAIT mode during 30 sec and go to ARM mode
2	All Entrances Closed	All kind of Unlock	DISARM Flash DISARM Buzzer	?
3	Any Entrance Opened			?
4	All Entrances Closed, After Lock Trunk or Hood Open	Trunk or Hood Open > Close	ARM Flash	?
5		Any Door Unlock		?
6	Any Door Open, Trunk or Hood Open	RKE Unlock	DISARM Flash DISARM Buzzer	?
7	?	MTS, Passive Unlock	DISARM Flash	?
8	ARM mode	Any Entrance Opened	ALARM Flash ALARM Buzzer	?

Function Description

State Description

1.

DISARM to DISARM Condition 1 State Description Initial Condition • DISARM STATE  • Key Out state(Key Off )  • Any Door is Open(Any Door Open On)  Event Unlock by RKE(RKE Unlock Off > On)  Action • DISARM Flashing(Disarm Flasher On)  • DISARM Buzzer Activation(Disarm Buzzer On)   • State does not changed  Condition 2 State Description Initial Condition • DISARM STATE  • Any Door is Open (Any Door Open On)  Event Unlock by SMK(Passive Access Unlock Off> On)    Action • DISARM Flashing(Disarm Flasher On)  • DISARM Buzzer Activation(Disarm Buzzer On)   • State does not changed  Condition 3 State Description Initial Condition • DISARM STATE Event Key On state (Key On)  Action • Security IND is Off(Security IND Off).  • State does not changed  Condition 4 State Description Initial Condition • DISARM STATE Event Key Off state (Key Off On)  Action • Security IND is Blinking (Security IND Blinking; 0.32sec:On/2sec:Off).  • State does not changed

2.

ARMWAIT to DISARM Condition 1 State Description Initial Condition • ARMWAIT STATE Event 1. Key In (Key In On) or  2. Fob In (Fob In On) or  3. Any Door is Open(Any Door Open On) or  4. Hood is Open(Hood SW On) or  5. Trunk is Open(Trunk Status On) or  6. Any Door is Unlock(Any Door Unlock On)  Action • State go to DISARM State Condition 2 State Description Initial Condition • ARMWAIT STATE  • Mechanical key ARM/DISARM Option is enable(MECH Opt On)  Event Unlock by Mechanical Key(DRV Key Unlock Off > On) Action • State go to DISARM State Condition 3 State Description Initial Condition • ARMWAIT STATE Event 1. Authenticate by Immobilizer System(TP_AUTH On) or  2. Authenticate by SMK (PIC_AUTH On) or  3. Pre-Authenticate by valid Fob (TP FeedBack On)   Action • State go to DISARM State

3.

ARM to DISARM Condition 1 State Description Initial Condition • ARM STATE Event 1. Authenticate by Immobilizer System(TP AUTH On) or  2. Authenticate by SMK (PIC AUTH On) or  3. Pre-Authenticate by valid Fob (TP FeedBack On)   Action • State go to DISARM State Condition 2 State Description Initial Condition • ARM STATE  • No China Option (China Option Off)   Event Key In and IGN1 On and IGN2 On(Key IGN On) Action • State go to DISARM State Condition 3 State Description Initial Condition • ARM STATE  • Mechanical key ARM/DISARM Option is enable(MECH Opt On)  Event Unlock by Mechanical Key (DRV Key Unlock Off > On) Action • State go to DISARM State

4.

ARM HOLD to DISARM Condition 1 State Description Initial Condition • ARMHOLD STATE Event 1. Authenticate by Immobilizer System(TP AUTH On) or  2. Authenticate by SMK (PIC AUTH On) or  3. Pre-Authenticate by valid Fob (TP FeedBack On)   Action • State go to DISARM State Condition 2 State Description Initial Condition • ARMHOLD STATE  • No China Option (China Option Off)   Event Key In and IGN1 On and IGN2 On(Key IGN On) Action • State go to DISARM State Condition 3 State Description Initial Condition • ARMHOLD STATE  • Mechanical key ARM/DISARM Option is enable(MECH Opt On)  Event Unlock by Mechanical Key (DRV Key Unlock Off > On) Action • State go to DISARM State

5.

AUTO LOCK TIMER1 to DISARM Condition 1 State Description Initial Condition • AUTOLOCKTIMER1 STATE Event 1. Key In(Key In On) or  2. Fob In (Fob In On) or  3. Any Door is Open(Any Door Open On) or  4. Hood is Open(Hood SW On) or  5. Trunk is Open(Trunk Status On) or  6. Authenticate by Immobilizer System(TP AUTH On) or  7. Authenticate by SMK (PIC AUTH On) or 8. Pre-Authenticate by valid Fob (TP FeedBack On) or  9. Lock by RKE/SMK/AutoLock/Mechanical key with option mechanical set  but locking failed ( Lock Confirm Fail Off > On)  Action • State go to DISARM State  • Auto Lock Off

6.

AUTO LOCK TIMER2 to DISARM Condition 1 State Description Initial Condition • AUTOLOCKTIMER2 STATE Event 1. Key In On(Key In On) or  2. Fob In (Fob In On) or  3. Any Door is Open(Any Door Open On) or  4. Hood is Open(Hood SW On && Hood Open Off) or  5. Trunk is Open(Trunk Status On && Trunk Open Off) or  6. Authenticate by Immobilizer System(TP AUTH On) or  7. Authenticate by SMK (PIC AUTH On)  or  8. Pre-Authenticate by valid Fob (TP FeedBack On) or  9. Lock by RKE/SMK/AutoLock/Mechanical key with option mechanical set  but locking failed (Lock Confirm Fail Off > On)    Action • Hood Open Off  • Trunk Open Off  • Auto Lock Off  • State go to DISARM State

7.

PREARM to DISARM Condition 1 State Description Initial Condition • PREARM STATE Event 1. Key In On(Key In On) or  2. Fob In (Fob In On) or  3. Authenticate by Immobilizer System(TP AUTH On) or  4. Authenticate by SMK (PIC AUTH On) or  5. Pre-Authenticate by valid Fob (TP FeedBack On) or  6. All Doors are Close (All Doors Close On) and Hood is Close  (Hood SW Off) and Trunk is Close(Trunk Status Off) and  Any Door is Unlock (Any Door Unlock On) Action • State go to DISARM State Condition 2 State Description Initial Condition • PREARM STATE  • Any Door is Open(Any Door Open On)   Event 1. Unlock by SMK(Passive Access Unlock Off > On) or 2. Unlock by RKE(RKE Unlock Off > On)   Action • DISARM Flashing(Disarm Flasher On)  • DISARM Buzzer Activation(Disarm Buzzer On)   • State go to DISARM State

8.

REARM to DISARM Condition 1 State Description Initial Condition • REARM STATE Event 1. Trunk release by RKE(RKE Trunk Off > On) or  2. Trunk release by SMK (P TRUNK Off > On) or  3. Lock by RKE/SMK but Locking is Failed  ( Lock Confirm Fail Off > On) or  4. Authenticate by Immobilizer System(TP AUTH On) or  5. Authenticate by SMK (PIC AUTH On) or  6. Alternator Input Level is High during 3sec (Alt L Alarm Release On) or  7. Pre-Authenticate by valid Fob (TP FeedBack On)   Action • Engine Start Inhibition state is released (Start Inhibition Off)  • State go to DISARM State  Condition 2 State Description Initial Condition • REARM STATE at Non China Option (China Option Off)  Event Key In On and IGN1 On and IGN2 On during 30sec ( Key IGN Alarm Release On) Action • Engine Start Inhibition state is released (Start Inhibition Off)  • State go to DISARM State  Condition 3 State Description Initial Condition • REARM STATE  • Mechanical key ARM/DISARM Option is enable(MECH Opt On)  Event 1. Unlock by Mechanical Key (DRV Key Unlock Off > On) or  2. Lock by Mechanical Key but Locking is Failed(Lock Confirm Fail Off>On) or  3. Trunk Release by Mechanical Key (Trunk Key Unlock SW Off > On)  Action • Engine Start Inhibition state is released (Start Inhibition Off)  • State go to DISARM State

9.

ALARM to DISARM Condition 1 State Description Initial Condition • ALARM STATE Event 1. Trunk release by RKE(RKE Trunk Off > On) or  2. Trunk release by SMK(P TRUNK Off > On) or  3. Lock by RKE/SMK but Locking is FaiIed (Lock Confirm Fail Off > On) or  4. Authenticate by Immobilizer System(TP AUTH On) or  5. Authenticate by SMK (PIC AUTH On)  or  6. Pre-Authenticate by valid Fob (TP FeedBack On) or  7. Alternator Input Level is High(Alt L On) during 3sec (Alt L Alarm Release On)  Action • Stop alarm flashing (Alarm Flasher Off)  • Stop Burglar Alarm Horn(Burglar Alarm Horn Off/ Horn Off)  • Engine Start Inhibition state is released (Start Inhibition Off)  • State go to DISARM State  Condition 2 State Description Initial Condition • ALARM STATE at Non China Option(China Option Off)  Event Key In and IGN1 On and IGN2 On during 30sec ( Key IGN Alarm Release On) Action • Stop alarm flashing (Alarm Flasher Off)  • Stop Burglar Alarm Horn(Burglar Alarm Horn Off/ Horn Off)  • Engine Start Inhibition state is released (Start Inhibition Off)  • State go to DISARM State  Condition 3 State Description Initial Condition • ALARM STATE  • Mechanical key ARM/DISARM Option is enable(MECH Opt On)  Event 1. Unlock by Mechanical Key (DRV Key Unlock Off > On) or  2. Trunk release by Mechanical Key(Trunk Key Unlock SW Off > On) or  3. Lock by Mechanical Key but Locking is FaiIed(Lock Confirm Fail Off > On)   Action • Stop alarm flashing (Alarm Flasher Off)  • Stop Burglar Alarm Horn(Burglar Alarm Horn Off/ Horn Off)  • Engine Start Inhibition state is released (Start Inhibition Off)  • State go to DISARM State  Condition 4 State Description Initial Condition • ALARM STATE  • Any Door is Open(Any Door Open On)  Event 1. Unlock by SMK(Passive Access Unlock Off > On) or  2. Unlock by RKE (RKE Unlock Off > On)   Action • DISARM Flashing(Disarm Flasher On)  • DISARM Buzzer Activation(Disarm Buzzer On)   • Stop alarm flashing (Alarm Flasher Off)  • Stop Burglar Alarm Horn(Burglar Alarm Horn Off/ Horn Off)  • Engine Start Inhibition state is released (Start Inhibition Off)  • State go to DISARM State

1.

DISARM to ARMWAIT Condition 1 State Description Initial Condition • DISARM STATE • Key Out state(Key Off On) • All Doors are Close(All Doors Close On) • Hood is Close(Hood SW Off) • Trunk is Close(Trunk Status Off) Event 1. Lock by RKE and Locking is not Failed (RKE Lock Confirm Success Off > On)   or 2. Lock by SMK and Locking is not Failed (Passive Lock Confirm Success Off > On) Action • ARM Flashing(Arm Flasher On) • ARM Buzzer Activation(Arm Buzzer On) • Start ArmWaitTimer • State go to ARMWAIT State • Burglar alarm State1 • Along with burglar alarm State 1 send FOB1 and FOB2 signals with values  depending on memorized FOB ID Fob1 and Fob2 Condition 2 State Description Initial Condition • DISARM STATE • Key Out state(Key Off On) • All Doors are Close(All Doors Close On) • Hood is Close(Hood switch Off) • Trunk is Close(Trunk Status Off) • Mechanical key ARM/DISARM Option is enable(MECH Opt On) Event Lock by Mechanical Key and Locking is not Failed (Key Lock Confirm Success Off > On) Action • Start ArmWaitTimer • State go to ARMWAIT State • Burglar alarm State1 • Along with Burglar alarm State 1 send FOB1 and FOB2 signals with values  depending on memorized FOB ID Fob1 and Fob2 Condition 3 State Description Initial Condition • DISARM STATE • Key Out state(Key Off On) • All Doors are Lock(All Doors Lock On) • Hood is Close(Hood SW Off) • Trunk is Close(Trunk Status Off) • Mechanical key ARM/DISARM Option is enable (MECH Opt On) Event All Doors are Close (All Doors Close Off > On) Action • Start ArmWaitTimer • State go to ARMWAIT State • Burglar alarm State1 • Along with burglar alarm State 1 send FOB1 aand FOB2 signals with values set to 0

2.

ARMWAIT to ARMWAIT Condition 1 State Description Initial Condition • ARMWAIT STATE Event 1. Lock by RKE and Locking is not Failed (RKE Lock Confirm Success Off > On)   or 2. Lock by SMK and Locking is not Failed (Passive Lock Confirm Success Off > On) Action • ARM Flashing (Arm Flasher On) • ARM Buzzer Activation (Arm Buzzer On) • State does not changed

3.

AUTO LOCK TIMER1 to ARMWAIT Condition 1 State Description Initial Condition • AUTO LOCK TIMER1 STATE • All Doors are Close(All Doors Close On) • Hood is Close(Hood switch Off) • Trunk is Close(Trunk Status Off) Event 1. Lock by RKE and Locking is not Failed (RKE Lock Confirm Success Off > On)   or 2. Lock by SMK and Locking is not Failed (Passive Lock Confirm Success Off > On) Action • ARM Flashing (Arm Flasher On) • ARM Buzzer Activation (Arm Buzzer On) • Start ArmWaitTimer • Auto Lock Off • State go to ARMWAIT State • Burglar alarm State1 • Along with burglar alarm State 1 send FOB1 and FOB2 signals with values  depending on memorized FOB ID Fob1 and Fob2 Condition 2 State Description Initial Condition • AUTOLOCKTIMER1 STATE • All Doors are Close (All Doors Close On) • Hood is Close (Hood switch Off) • Trunk is Close (Trunk Status Off) • Mechanical key ARM/DISARM Option is enable (MECH Opt On) Event Lock by Mechanical Key and Locking is not Failed (Key Lock Confirm Success Off > On) Action • Start ArmWait Timer • State go to ARMWAIT State • Burglar alarm State1 • Auto Lock Off • Along with burglar alarm State 1 send FOB1 and FOB2 signals with values  depending on memorized FOB ID Fob1 and Fob2 Condition 3 State Description Initial Condition • AUTOLOCKTIMER1 STATE • All Doors are Close (All Doors Close On) • Hood is Close (Hood SW Off) • Trunk is Close (Trunk Status Off) Event Lock by Auto Lock (AutoLock1Timer ? AutoLock1Time) and Locking is not Failed (Auto Lock Confirm Success Off > On) Action • ARM Flashing (Arm Flasher On) • Start ArmWaitTimer • State go to ARMWAIT State • Burglar alarm State1 • Auto Lock Off • Along with burglar alarm State 1 send FOB1 and FOB2 signals with values  depending on memorized FOB ID Fob1 and Fob2

4.

PREARM to ARMWAIT Condition 1 State Description Initial Condition • PREARM STATE Event Clear TrunkMarker (Trunk Marker Off) and All Doors are Close (All Doors Close On) and Hood is Close (Hood SW Off) and Trunk is Close (Trunk Status Off) and All Doors are Lock (All Doors Lock On) Action • ARM Flashing (Arm Flasher On) • Start ArmWaitTimer • State go to ARMWAIT State • Burglar alarm State1 • Along with burglar alarm State 1 send FOB1 and FOB2 signals with values set to 0

5.

REARM to ARMWAIT Condition 1 State Description Initial Condition • REARM STATE • Key Out state (Key Off On) • All Doors are Close (All Doors Close On) • Hood is Close (Hood SW Off) • Trunk is Close (Trunk Status Off) Event 1. Lock by RKE and Locking is not Failed (RKE Lock Confirm Success Off > On)   or 2. Lock by SMK and Locking is not Failed (Passive Lock Confirm Success Off > On) Action • Engine Start Inhibition state is released (Start Inhibition Off) • ARM Flashing (Arm Flasher On) • ARM Buzzer Activation (Arm Buzzer On) • Start ArmWaitTimer • State go to ARMWAIT State • Burglar alarm State1 Condition 2 State Description Initial Condition • REARM STATE • Key Out state (Key Off On) • All Doors are Close (All Doors Close On) • Hood is Close (Hood SW Off) • Trunk is Close(Trunk Status Off) • Mechanical key ARM/DISARM Option is enable (MECH Opt On) Event Lock by Mechanical Key and Locking is not Failed (Key Lock Confirm Success Off > On) Action • Engine Start Inhibition state is released (Start Inhibition Off) • Start ArmWaitTimer • State go to ARMWAIT State • Burglar alarm State1

6.

ALARM to ARMWAIT Condition 1 State Description Initial Condition • ALARM STATE • Key Out state(Key Off ) • All Doors are Close(All Doors Close On) • Hood is Close(Hood SW Off) • Trunk is Close(Trunk Status Off) Event 1. Lock by RKE and Locking is not Failed (RKE Lock Confirm Success Off > On)   or 2. Lock by SMK and Locking is not Failed (Passive Lock Confirm Success Off > On) Action • Stop alarm flashing. (Alarm Flasher Off) • Stop Burglar Alarm Horn (Burglar Alarm Horn = Off/ Horn Off) • Engine Start Inhibition state is released (Start Inhibition Off) • ARM Flashing (Arm Flasher On) • ARM Buzzer Activation (Arm Buzzer On) • Start ArmWaitTimer • State go to ARMWAIT State • Burglar alarm State1 Condition 2 State Description Initial Condition • ALARM STATE • Key Out state(Key Off ) • All Doors are Close(All Doors Close On) • Hood is Close(Hood SW Off) • Trunk is Close(Trunk Status Off) • Mechanical key ARM/DISARM Option is enable(MECH Opt On) Event Lock by Mechanical Key and Locking is not Failed (Key Lock Confirm Success Off > On) Action • Stop alarm flashing. (Alarm Flasher Off) • Stop Burglar Alarm Horn(Burglar Alarm Horn Off/ Horn Off) • Engine Start Inhibition state is released (Start Inhibition Off) • Start ArmWaitTimer • State go to ARMWAIT State • Burglar alarm State1

1.	ARMWAIT to ARM Condition 1 State Description Initial Condition • ARMWAIT STATE Event ArmWaitTimer ? ArmWaitTime Action • Cancel ArmWaitTimer • State go to ARM State

2.

ARM to ARM Condition 1 State Description Initial Condition • ARM STATE • Key Out state(Key Off) Event 1. Lock by RKE and Locking is not Failed (RKE Lock Confirm Success Off > On)   or 2. Lock by SMK and Locking is not Failed (Passive Lock Confirm Success Off > On) Action • ARM Flashing(Arm Flasher On) • ARM Buzzer Activation(Arm Buzzer On) • State does not change

3.	ARMHOLD to ARM Condition 1 State Description Initial Condition • ARMHOLD STATE Event Trunk is Close(Trunk Status Off) and Trunk Timer is expired. (Trunk Timer ? Trunk Release Time Out), Action • Cancel Trunk Timer • State go to ARM State

1.

ARM to ARMHOLD Condition 1 State Description Initial Condition • ARM STATE Event 1. Trunk release by RKE(RKE Trunk Off > On) or 2. Trunk release by SMK (P TRUNK Off > On)       Action • State go to ARMHOLD State • Start Trunk Timer Condition 2 State Description Initial Condition • ARM STATE • Mechanical key ARM/DISARM Option is enable (MECH Opt On) Event Trunk release by Mechanical Key (Trunk Key Unlock SW Off > On)  Action • State go to ARMHOLD State • Start Trunk Timer

2.

ARMHOLD to ARMHOLD Condition 1 State Description Initial Condition • ARMHOLD STATE Event Trunk closed(Trunk Status On > Off)       Action • State remains in ARMHOLD State • Start Trunk Timer Condition 2 State Description Initial Condition • ARMHOLD STATE Event Trunk is open (Trunk Status On)  Action • State remains in ARMHOLD State • Cancel Trunk Timer

1.

DISARM to AUTOLOCKTIMER1 Condition 1 State Description Initial Condition • DISARM STATE • Key Out state(Key Off On) • All Doors are Close(All Doors Close On) • Hood is Close(Hood SW Off) • Trunk is Close(Trunk Status Off) Event 1. Unlock by SMK(Passive Access Unlock Off > On) or 2. Unlock by RKE(RKE Unlock Off > On) Action • DISARM Flashing(Disarm Flasher On) • DISARM Buzzer Activation(Disarm Buzzer On) • Start Auto Lock1Timer • State go to AUTO LOCK TIMER1 State

2.

ARMWAIT to AUTOLOCKTIMER1 Condition 1 State Description Initial Condition • ARMWAIT STATE • All Doors are Close (All Doors Close On) • Hood is Close(Hood SW Off) • Trunk is Close(Trunk Status Off) Event 1. Unlock by SMK(Passive Access Unlock Off > On) or 2. Unlock by RKE(RKE Unlock Off > On) Action • DISARM Flashing(Disarm Flasher On) • DISARM Buzzer Activation(Disarm Buzzer On) • Start AutoLock1Timer • State go to AUTOLOCKTIMER1 State

3.

ARM to AUTOLOCKTIMER1 Condition 1 State Description Initial Condition • ARM STATE • All Doors are Close(All Doors Close On) • Hood is Close(Hood switch Off) • Trunk is Close(Trunk Status Off) Event 1. Unlock by SMK(Passive Access Unlock Off > On) or 2. Unlock by RKE(RKE Unlock Off > On) Action • DISARM Flashing(Disarm Flasher On) • DISARM Buzzer Activation(Disarm Buzzer On) • Start AutoLock1Timer • State go to AUTOLOCKTIMER1 State

4.

AUTOLOCKTIMER1 to AUTOLOCKTIMER1 Condition 1 State Description Initial Condition • AUTOLOCKTIMER1 STATE • All Doors are Close(All Doors Close On) • Hood is Close(Hood SW Off) • Trunk is Close(Trunk Status Off) Event 1. Unlock by SMK(Passive Access Unlock Off > On) or 2. Unlock by RKE(RKE Unlock Off > On) Action • DISARM Flashing(Disarm Flasher On) • DISARM Buzzer Activation(Disarm Buzzer On) • Restart AutoLock1Timer • State does not changed Condition 2 State Description Initial Condition • AUTOLOCKTIMER1 STATE Event 1. AutoLock1Timer timer is elapsed (AutoLock1Timer ? AutoLock1Time) Action • Cancel AutoLock1Timer • Lock by Autolock (Auto Lock On; Relock On) • State does not changed

5.

REARM to AUTOLOCKTIMER1 Condition 1 State Description Initial Condition • REARM STATE • All Doors are Close(All Doors Close On) • Hood is Close(Hood SW Off) • Trunk is Close(Trunk Status Off) Event 1. Unlock by SMK(Passive Access Unlock Off > On) or 2. Unlock by RKE(RKE Unlock Off > On) Action • Engine Start Inhibition state is released (Start Inhibition Off) • DISARM Flashing(Disarm Flasher On) • DISARM Buzzer Activation(Disarm Buzzer On) • Start AutoLock1Timer • State go to AUTOLOCKTIMER1 State

6.

ALARM to AUTOLOCKTIMER1 Condition 1 State Description Initial Condition • ALARM STATE • All Doors are Close(All Doors Close On) • Hood is Close(Hood SW Off) • Trunk is Close(Trunk Status Off) Event 1. Unlock by SMK(Passive Access Unlock Off > On) or 2. Unlock by RKE(RKE Unlock Off > On) Action • Stop alarm flashing. (Alarm Flasher Off) • Stop Burglar Alarm Horn(Burglar Alarm Horn Off/ Horn Off) • Engine Start Inhibition state is released (Start Inhibition Off) • DISARM Flashing(Disarm Flasher On) • DISARM Buzzer Activation(Disarm Buzzer On) • Start AutoLock1Timer • State go to AUTOLOCKTIMER1 State

1.

DISARM to AUTOLOCKTIMER2 Condition 1 State Description Initial Condition • DISARM STATE • Key Out state (Key Off) • All Doors are Close (All Doors Close On) • Hood is Open (Hood SW On) • Trunk is Close (Trunk Status Off) Event 1. Unlock by SMK (Passive Access Unlock Off > On) or 2. Unlock by RKE (RKE Unlock Off > On) Action • DISARM Flashing (Disarm Flasher On) • DISARM Buzzer Activation (Disarm Buzzer On) • Memorize Hood Open State (Hood Open On) • Start Auto Lock2 Timer • State go to AUTO LOCK TIMER2 State Condition 2 State Description Initial Condition • DISARM STATE • Key Out state(Key Off On) • All Doors are Close(All Doors Close On) • Hood is Close(Hood SW Off) • Trunk is Open(Trunk Status On) Event 1. Unlock by SMK(Passive Access Unlock Off > On) or 2. Unlock by RKE(RKE Unlock Off > On) Action • DISARM Flashing(Disarm Flasher On) • DISARM Buzzer Activation(Disarm Buzzer On) • Memorize Trunk Open State(Trunk Open On) • Start AutoLock2Timer • State go to AUTOLOCKTIMER2 State Condition 3 State Description Initial Condition • DISARM STATE • Key Out state(Key Off On) • All Doors are Close(All Doors Close On) • Hood is Open(Hood SW On) • Trunk is Open(Trunk Status On) Event 1. Unlock by SMK(Passive Access Unlock Off > On) or 2. Unlock by RKE(RKE Unlock Off > On) Action • DISARM Flashing(Disarm Flasher On) • DISARM Buzzer Activation(Disarm Buzzer On) • Memorize Hood Open State(Hood Open On) • Memorize Trunk Open State(Trunk Open On) • Start AutoLock2Timer • State go to AUTOLOCKTIMER2 State

2.

ARMHOLD to AUTOLOCKTIMER2 Condition 1 State Description Initial Condition • ARMHOLD STATE • All Doors are Close(All Doors Close On) Event 1. Unlock by SMK(Passive Access Unlock Off > On) or 2. Unlock by RKE(RKE Unlock Off > On) Action • DISARM Flashing(Disarm Flasher On) • DISARM Buzzer Activation(Disarm Buzzer On) • Memorize Trunk Open State(Trunk Open On) • Start AutoLock2Timer • State go to AUTOLOCKTIMER2 State

3.

AUTOLOCKTIMER2 to AUTOLOCKTIMER2 Condition 1 State Description Initial Condition • AUTOLOCKTIMER2 STATE Event 1. Unlock by SMK(Passive Access Unlock Off > On) or 2. Unlock by RKE(RKE Unlock Off > On) Action • DISARM Flashing(Disarm Flasher On) • DISARM Buzzer Activation(Disarm Buzzer On) • Restart AutoLock2Timer • State does not changed Condition 2 State Description Initial Condition • AUTOLOCKTIMER2 STATE Event AutoLock2Timer timer is elapsed (Auto Lock2 Timer ? AutoLock2Time)  Action • Cancel AutoLock2Timer • Lock by Autolock (Auto Lock On; Relock On) • State does not changed

4.

PREARM to AUTOLOCKTIMER2 Condition 1 State Description Initial Condition • PREARM STATE • All Doors are Close (All Doors Close On) • Hood is Open (Hood switch On) • Trunk is Close(Trunk Status Off) Event 1. Unlock by SMK (Passive Access Unlock Off > On) or 2. Unlock by RKE (RKE Unlock Off > On) Action • DISARM Flashing (Disarm Flasher On) • DISARM Buzzer Activation (Disarm Buzzer On) • Memorize Hood Open State (Hood Open On) • Start AutoLock2Timer • State go to AUTOLOCKTIMER2 State Condition 2 State Description Initial Condition • PREARM STATE • All Doors are Close (All Doors Close On) • Hood is Close (Hood switch Off) • Trunk is Open (Trunk Status On) Event 1. Unlock by SMK (Passive Access Unlock Off > On) or 2. Unlock by RKE (RKE Unlock Off > On) Action • DISARM Flashing (Disarm Flasher On) • DISARM Buzzer Activation (Disarm Buzzer On) • Memorize Trunk Open State (Trunk Open On) • Start AutoLock2 Timer • State go to AUTO LOCK TIMER2 State Condition 3 State Description Initial Condition • PREARM STATE • All Doors are Close(All Doors Close On) • Hood is Open (Hood switch On) • Trunk is Open (Trunk Status On) Event 1. Unlock by SMK(Passive Access Unlock Off > On) or 2. Unlock by RKE(RKE Unlock Off > On) Action • DISARM Flashing(Disarm Flasher On) • DISARM Buzzer Activation (Disarm Buzzer On) • Memorize Hood Open State (Hood Open On) • Memorize Trunk Open State (Trunk Open On) • Start Auto Lock2Timer • State go to AUTOLOCKTIMER2 State

5.

ALARM to AUTOLOCKTIMER2 Condition 1 State Description Initial Condition • ALARM STATE • All Doors are Close(All Doors Close On) • Hood is Open(Hood switch On) • Trunk is Close(Trunk Status Off) Event 1. Unlock by SMK (Passive Access Unlock Off > On) or 2. Unlock by RKE (RKE Unlock Off > On) Action • Stop alarm flashing. (Alarm Flasher Off) • Stop Burglar Alarm Horn (Burglar alarm Horn Off/ Horn Off) • Engine Start Inhibition state is released (Start Inhibition Off) • DISARM Flashing(Disarm Flasher On) • DISARM Buzzer Activation (Disarm Buzzer On) • Memorize Hood Open State (Hood Open On) • Start AutoLock2 Timer • State go to AUTO LOCK TIMER2 State Condition 2 State Description Initial Condition • ALARM STATE • All Doors are Close (All Doors Close On) • Hood is Close (Hood switch Off) • Trunk is Open (Trunk Status On) Event 1. Unlock by SMK (Passive Access Unlock Off > On) or 2. Unlock by RKE (RKE Unlock Off > On) Action • Stop alarm flashing. (Alarm Flasher Off) • Stop Burglar Alarm Horn (Burglar Alarm Horn Off/ Horn Off) • Engine Start Inhibition state is released (Start Inhibition Off) • DISARM Flashing (Disarm Flasher On) • DISARM Buzzer Activation (Disarm Buzzer On) • Memorize Trunk Open State ( Trunk Open On) • Start Auto Lock2 Timer • State go to AUTO LOCK TIMER2 State Condition 3 State Description Initial Condition • ALARM STATE • All Doors are Close (All Doors Close On) • Hood is Close (Hood switch On) • Trunk is Open (Trunk Status On) Event 1. Unlock by SMK (Passive Access Unlock Off > On) or 2. Unlock by RKE (RKE Unlock Off > On) Action • Stop alarm flashing. (Alarm Flasher Off) • Stop Burglar Alarm Horn (Burglar Alarm Horn Off/ Horn Off) • Engine Start Inhibition state is released (Start Inhibition Off) • DISARM Flashing (Disarm Flasher On) • DISARM Buzzer Activation (Disarm Buzzer On) • Memorize Hood Open State (Hood Open On) • Memorize Trunk Open State (Trunk Open On) • Start AutoLock2 Timer • State go to AUTO LOCK TIMER2 State

1.

DISARM to PREARM Condition 1 State Description Initial Condition • DISARM STATE • Key Out state(Key Off On) • Any Door is Open (Any Door Open On) or Hood is Open (Hood switch On) or Trunk is Open(Trunk Status On) Event 1. Lock by RKE and Locking is not Failed (RKE Lock Confirm Success Off > On)   or 2. Lock by SMK and Locking is not Failed (Passive Lock Confirm Success Off > On) Action • State go to PREARM State • Reset Trunk Marker(Trunk Marker Off) Condition 2 State Description Initial Condition • DISARM STATE • Key Out state(Key Off On) • Any Door is Open (Any Door Open On) or (Hood is Open (Hood SW On) or Trunk is Open (Trunk Status On) • Mechanical key ARM/DISARM Option is enable (MECH Opt On) Event Lock by Mechanical Key and Locking is not Failed (Key Lock Confirm Success Off > On) Action • State go to PREARM State • Reset Trunk Marker (Trunk Marker Off) Condition 3 State Description Initial Condition • DISARM STATE • Key Out state (Key Off On) • Any Door is Open (Any Door Open On) • Hood is Open (Hood SW On) or Trunk is Open (Trunk Status On) • All Doors are Lock (All Doors Lock On) • Mechanical key ARM/DISARM Option is enable (MECH Opt On) Event All Doors are Close (All Doors Close On)  Action • State go to PREARM State • Reset Trunk Marker (Trunk Marker Off)

2.

ARMWAIT to PREARM Condition 1 State Description Initial Condition • ARMWAIT STATE Event 1. Trunk release by RKE (RKE Trunk Off > On) or 2. Trunk release by SMK (TRUNK Off > On) Action • Start Trunk Timer • Set Trunk Marker (Trunk Marker On) • State go to PREARM State Condition 2 State Description Initial Condition • ARMWAIT STATE • Mechanical key ARM/DISARM Option is enable (MECH Opt On) Event Trunk release by Mechanical Key (Trunk Key Unlock switch Off > On)  Action • Start Trunk Timer • Set Trunk Marker(Trunk Marker On) • State go to PREARM State

3.

ARMHOLD to PREARM Condition 1 State Description Initial Condition • ARMHOLD STATE Event 1. Lock by RKE(RKE Lock Off > On) or 2. Lock by SMK(Passive Access Lock Off > On) Action • State go to PREARM State • Reset Trunk Marker(Trunk Marker Off) Condition 2 State Description Initial Condition • ARMHOLD STATE • Mechanical key ARM/DISARM Option is enable(MECH Opt On) Event Lock by Mechanical Key(DRV Key Lock Off > On)  Action • State go to PREARM State • Reset Trunk Marker(Trunk Marker Off)

4.

AUTOLOCKTIMER2 to PREARM Condition 1 State Description Initial Condition • AUTOLOCKTIMER2 STATE Event 1. Lock by RKE(RKE Lock Off > On) and Locking is not Failed (Lock Confirm Fail Off) or 2. Lock by SMK(Passive Access Lock Off > On) and Locking is not Failed (Lock Confirm Fail Off) or 3. Lock by AutoLock Auto Lock On (AutoLock2Timer ? AutoLock2Time) and Locking is not Failed (Lock Confirm Fail Off) Action • State go to PREARM State • Hood Open Off • Trunk Open Off • Auto Lock Off • Reset Trunk Marker(Trunk Marker Off) Condition 2 State Description Initial Condition • AUTOLOCKTIMER2 STATE • Mechanical key ARM/DISARM Option is enable(MECH Opt On) Event Lock by Mechanical Key and Locking is not Failed (Key Lock Confirm Success Off > On) Action • State go to PREARM State • Hood Open Off • Trunk Open Off • Auto Lock Off • Reset TrunkMarker(Trunk Marker Off)

5.	PREARM to PREARM Condition 1 State Description Initial Condition • PREARM STATE • Trunk is Close(Trunk Status Off) Event 1. Trunk is open(Trunk Status On) 2. Trunk Timer ? Trunk Release Time Out Action • Cancel Trunk Timer • Reset Trunk Marker(Trunk Marker Off) • State does not change

6.

ALARM to PREARM Condition 1 State Description Initial Condition • ALARM STATE • Key Out state(Key Off) • Any Door is Open(Any Door Open On) or Hood is Open(Hood SW On) or Trunk is Open(Trunk Status On) Event 1. Lock by RKE(RKE Lock Off > On) and Locking is not Failed (Lock Confirm Fail Off) or 2. Lock by SMK(Passive Access Lock Off > On) and Locking is not Failed (Lock Confirm Fail Off) Action • Stop alarm flashing. (Alarm Flasher Off) • Engine Start Inhibition state is released (Start Inhibition Off) • Reset Trunk Marker(Trunk Marker Off) • State go to PREARM State Condition 2 State Description Initial Condition • AUTOLOCKTIMER2 STATE • Key Out state(Key Off On) • Any Door is Open(Any Door Open On) or Hood is Open(Hood SW On) or Trunk is Open(Trunk Status On) • Mechanical key ARM/DISARM Option is enable(MECH Opt On) Event Lock by Mechanical Key(DRV Key Lock Off > On) and Locking is not Failed (Lock Confirm Fail Off)  Action • Stop alarm flashing. (Alarm Flasher Off) • Engine Start Inhibition state is released (Start Inhibition Off) • Reset Trunk Marker(Trunk Marker Off) • State go to PREARM State

1.

ALARM to REARM Condition 1 State Description Initial Condition • ALARM STATE • Non China Option (China Option Off) Event All Doors are Close(All Doors Close On) and Hood is Close(Hood SW Off) Trunk is Close(Trunk Status Off) and Finish ALARM Flashing (Alarm Flasher Off) Action • State go to REARM State Condition 2 State Description Initial Condition • ALARM STATE • China Option (China Option On) Event Key Off  and All Doors are Close(All Doors Close On) and Hood is Close(Hood SW Off) Trunk is Close(Trunk Status Off) and Finish ALARM Flashing (Alarm Flasher Off) Action • State go to REARM State

2.

REARM to REARM Condition 1 State Description Initial Condition • REARM STATE • Key In Off or IGN1 Off or IGN2 Off Event Key In On && IGN1 On && IGN2 On Action • Start KeyIGNTimer • State does not change Condition 2 State Description Initial Condition • REARM STATE • KeyIGNTimer < KeyIGNTime Event Key In Off or IGN1 Off or IGN2 Off Action • Cancel Key IGN Timer • State does not change Condition 3 State Description Initial Condition • REARM STATE Event Key IGN Timer ? Key IGN Time Action • Cancel Key IGN Timer • Key IGN Alarm Release On • State does not change Condition 4 State Description Initial Condition • REARM STATE • Alt L Off Event Alt L On Action • Start ALT L Alarm Release Timer • State does not change Condition 5 State Description Initial Condition • REARM STATE • ALT L Alarm Release Timer < ALT L Alarm Release Time Event Alt L Off Action • Cancel ALT L Alarm Release Timer • State does not change Condition 6 State Description Initial Condition • REARM STATE Event ALT L Alarm Release Timer ? ALT L Alarm Release Time Action • Cancel ALTLAlarmReleaseTimer • Alt l Alarm Release On • State does not change

1.

ARM to ALARM Condition 1 State Description Initial Condition • ARM STATE Event 1. Any Door is Open(Any Door Open On) or 2. Hood is Open(Hood SW On)  or 3. Trunk is Open(Trunk Status On) Action • Start Alarm Flashing (Alarm Flasher On) • Start Alarm Buzzer (Burglar Alarm Horn On/ Horn On) • Start Alarm Timer • Engine Start Inhibition is On (Start Inhibition On) • Key IGN Alarm Release Off • Alt l Alarm Release Off • Cancel Key IGN Timer • Cancel ALT L Alarm Release Timer • State go to ALARM State Condition 2 State Description Initial Condition • ARM STATE   at  China Option and Non Smart Key Option (Pic option Off && China Option On) Event Key On Action • Start Alarm Flashing (Alarm Flasher On) • Start Alarm Buzzer (Burglar Alarm Horn On/ Horn On) • Start Alarm Timer • Engine Start Inhibition is On (Start Inhibition On) • Key IGN Alarm Release Off • Alt l Alarm Release Off • Cancel Key IGN Timer • Cancel ALT L Alarm Release Timer • State go to ALARM State Condition 3 State Description Initial Condition • ARM STATE  at  China Option and Smart Key Option (Pic option On && China Option On) Event Key In On or Fob In On Action • Start Alarm Flashing (Alarm Flasher On) • Start Alarm Buzzer (Burglar Alarm Horn On/ Horn On) • Start Alarm Timer • Engine Start Inhibition is On (Start Inhibition On) • Key IGN Alarm Release Off • Alt l Alarm Release Off • Cancel Key IGN Timer • Cancel ALT L Alarm Release Timer • State go to ALARM State

2.

ARMHOLD to ALARM Condition 1 State Description Initial Condition • ARMHOLD STATE Event 1. Any Door is Open(Any Door Open On) or 2. Hood is Open(Hood SW On)  Action • Start Alarm Flashing (Alarm Flasher On) • Start Alarm Buzzer (Burglar Alarm Horn On/ Horn On) • Start Alarm Timer • Engine Start Inhibition is On (Start Inhibition On) • Key IGN Alarm Release Off • Alt l Alarm Release Off • Cancel Key IGN Timer • Cancel ALT L Alarm Release Timer • State go to ALARM State Condition 2 State Description Initial Condition ARMHOLD STATE at  China Option and Non Smart Key Option (Pic option Off && China Option On) Event Key On  Action • Start Alarm Flashing (Alarm Flasher On) • Start Alarm Buzzer (Burglar Alarm Horn On/ Horn On) • Start Alarm Timer • Engine Start Inhibition is On (Start Inhibition On) • Key IGN Alarm Release Off • Alt l Alarm Release Off • Cancel Key IGN Timer • Cancel ALT L Alarm Release Timer • State go to ALARM State Condition 3 State Description Initial Condition ARMHOLD STATE at  China Option and Smart Key Option (Pic option Off && China Option On) Event Key In On or Fob In On  Action • Start Alarm Flashing (Alarm Flasher On) • Start Alarm Buzzer (Burglar Alarm Horn On/ Horn On) • Start Alarm Timer • Engine Start Inhibition is On (Start Inhibition On) • Key IGN Alarm Release Off • Alt l Alarm Release Off • Cancel Key IGN Timer • Cancel ALT L Alarm Release Timer • State go to ALARM State

3.

REARM to ALARM Condition 1 State Description Initial Condition • REARM STATE Event 1. Any Door is Open (Any Door Open On) or 2. Hood is Open (Hood SW On)  or 3. Trunk is Open (Trunk Status On) Action • Start Alarm Flashing (Alarm Flasher On) • Start Alarm Buzzer (Burglar Alarm Horn On/ Horn On) • Start Alarm Timer • State go to ALARM State Condition 2 State Description Initial Condition • REARM STATE at  China Option and Non Smart Key Option (Pic option Off && China Option On) Event Key On Action • Start Alarm Flashing (Alarm Flasher On) • Start Alarm Buzzer (Burglar Alarm Horn On/ Horn On) • Start Alarm Timer • State go to ALARM State Condition 3 State Description Initial Condition • REARM STATE at  China Option and Smart Key Option (Pic option Off && China Option On) Event Key In On or Fob In On Action • Start Alarm Flashing (Alarm Flasher On) • Start Alarm Buzzer (Burglar Alarm Horn On/ Horn On) • Start Alarm Timer • State go to ALARM State

4.

ALARM to ALARM Condition 1 State Description Initial Condition • ALARM STATE Event Power RESET Action • Start Alarm Flashing (Alarm Flasher On) • Start Alarm Buzzer (Burglar Alarm Horn On/ Horn On) • Engine Start Inhibition is On (Start Inhibition On) • Start Alarm Timer • State does not change Condition 2 State Description Initial Condition • ALARM STATE Event AlarmTimer ? AlarmTime Action • Cancel AlarmTimer • Stop Alarm Flashing (Alarm Flasher Off) • Stop Alarm Buzzer (Burglar Alarm Horn Off/ Horn Off) • State does not change Condition 3 State Description Initial Condition • ALARM STATE • Key In Off or IGN1 Off or IGN2 Off Event Key In On & IGN1 On & IGN2 On Action • Start KeyIGNTimer • State does not change Condition 4 State Description Initial Condition • ALARM STATE • Key IGN Timer < Key IGN Time Event Key In Off or IGN1 Off or IGN2 Off Action • Cancel Key IGN Timer • State does not change Condition 5 State Description Initial Condition • ALARM STATE Event Key IGN Timer ? Key IGN Time Action • Cancel Key IGN Timer • Key IGN Alarm Release On • State does not change Condition 6 State Description Initial Condition • ALARM STATE • Alt L Off Event Alt L On Action • Start ALT L Alarm Release Timer • State does not change Condition 7 State Description Initial Condition • ALARM STATE • ALT L Alarm Release Timer < ALT L Alarm Release Time Event Alt L Off Action • Cancel ALT L Alarm Release Timer • State does not change Condition 8 State Description Initial Condition • ALARM STATE Event ALT L Alarm Release Timer ? ALT L Alarm Release Time Action • Cancel ALT L Alarm Release Timer • Alt l Alarm Release On • State does not change