Hyundai Equus Manuals

Hyundai Azera: Heater Unit Repair procedures - Heater - Heating,Ventilation, Air Conditioning - Hyundai Azera 2011-2025 Service ManualHyundai Azera: Heater Unit Repair procedures

Fifth generation HG (2011–2025) / Hyundai Azera 2011-2025 Service Manual / Heating,Ventilation, Air Conditioning / Heater / Heater Unit Repair procedures

Replacement
1.
Disconnect the negative (-) battery terminal.
2.
Recover the refrigerant with a recovery/ recycling/ charging station.
3.
When the engine is cool, drain the engine coolant from the radiator.
4.
Remove the expansion valve cover (A).

5.
Remove the bolts (A) and the expansion valve (B) from the evaporator core.
Plug or cap the lines immediately after disconnecting them to avoid moisture and dust contamination.
Tightening torque :
7.8 ~ 11.7 N.m ( 0.8 ~ 1.2 kgf.m, 5.7 ~ 8.6 Ib-ft)

6.
Disconnect the inlet (C) and outlet (D) heater hoses from the heater unit.

   
Engine coolant will run out when the hoses are disconnected; drain it into a clean drip pan. Be sure not to let coolant spill on electrical parts or painted surfaces. If any coolant spills, rinse it off immediately.
7.
Remove the crash pad.
8.
Remove the cowl cross member.
9.
Loosen the heater & blower assembly mounting bolts and then remove the heater & blower assembly (A).

10.
Remove the blower unit (B) from heater unit after loosening 3 screws.

11.
Installation is the reverse order of removal, and note these items :
A.
If you're installing a new evaporator, add refrigerant oil (ND-OIL8).
B.
Replace the O-rings with new ones at each fitting, and apply a thin coat of refrigerant oil before installing them. Be sure to use the right O-rings for R-134a to avoid leakage.
C.
Immediately after using the oil, replace the cap on the container, and seal it to avoid moisture absorption.
D.
Do not spill the refrigerant oil on the vehicle ; it may damage the paint ; if the refrigerant oil contacts the paint, wash it off immediately
E.
Apply sealant to the grommets.
F.
Make sure that there is no air leakage.
G.
Charge the system and test its performance.
H.
Do not interchange the inlet and outlet heater hoses and install the hose clamps securely.
I.
Refill the cooling system with engine coolant
Components and Components Location
Component Location Components 1. Heater Case (LH)2. Heater Case (RH)3. Separator4. Heater Case (Lower)5. Drain Hose6. Insulation7.Shower Duct (RH)8. Temp Actuator(PA)9. Temp Door Cam10. Evapora ...

Heater Core Repair procedures
Replacement 1. Disconnect the negative (-) battery terminal. 2. Recover the refrigerant with a recovery/ recycling/ charging station. 3. When the engine is cool, drain the engine coola ...

See also:

Power Out Side Mirror Switch Repair procedures
Inspection 1. The DDM inputs can be checked using the GDS. 2. To check the input value of door lock switch, select option "IPM". 3. Select option "DDM (Driver Door Module)". 4. Select ...

Rear Door Window Glass Components and Components Location
Component Location 1. Rear door window glass ...

Necessary inspections
Fluid levels, such as engine oil, engine coolant, brake fluid, and washer fluid should be checked on a regular basis, with the exact interval depending on the fluid. Further details are provided in ...

Categories

Hyundai Azera Manuals


© 2011-2025 Copyright www.hgmanual.com